Return
Home
FAQ
Page
MSDS
 
  Material Data Sheet
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME: Rapid Wax
SYNONYMS:
PRODUCT CODES: 001

MANUFACTURER: Microstar Dental
DIVISION:
ADDRESS: 1000 Lakes Parkway, Lawrenceville, GA 30043


EMERGENCY PHONE: 800-313-6427
CHEMTREC PHONE:
OTHER CALLS:
FAX PHONE: 770-339-3188

PRODUCT USE: DENTAL CROWNS
PREPARED BY: J. PITRE

SECTION 1 NOTES:


SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS

INGREDIENT:


CAS NO. % WT % VOL SARA 313 REPORTABLE


ppm mg/m3
OSHA PEL-TWA:
OSHA PEL STEL :
OSHA PEL CEILING:

ACGIH TLV-TWA:
ACGIH TLV STEL:
ACGIH TLV CEILING:

SECTION 2 NOTES:


SECTION 3: HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW: THE MANUFACTURER STATES THAT NO HAZARDOUS INGREDIENTS ARE
PRESENT IN THIS PRODUCT.


ROUTES OF ENTRY:

POTENTIAL HEALTH EFFECTS
EYES: MOLTEN WAX MAY BE SLIGHTLY
IRRITATION. SKIN: MOLTEN WAX WILL CAUSE BURNS.

SKIN: MOLTEN WAX MAY BE SLIGHTLY

INGESTION: no

INHALATION: MOLTEN WAX FUMES MAY CAUSE MILD (UPPER) RESPIRATORY IRRITATION. INGESTION:



ACUTE HEALTH HAZARDS:

CHRONIC HEALTH HAZARDS:


CARCINOGENICITY
OSHA: ACGIH: NTP: IARC:
OTHER:


SECTION 3 NOTES:


SECTION 4: FIRST AID MEASURES

EYES: FLUSH WITH WATER FOR AT LEAST 15 MIN. SEEK MEDICALATTENTION

SKIN: WHEN HOT WAX STRIKES THE SKIN, DRENCH OR IMMERSE
THE AREA IN WATER TO ASSIST COOLING. IF AVAILABLE, APPLY ICED WATER
OR ICE PACKS TO THE BURNED AREA. DO NOT REMOVE WAX FROM A BURN
AFTER IT HAS COOLED.

INGESTION: CONSULT MEDICAL PERSONNEL

INHALATION: REMOVE VICTIM TO FRESH AIR. SEEK
MEDICAL ATTENTION.


NOTES TO PHYSICIANS OR FIRST AID PROVIDERS:


SECTION 4 NOTES:


SECTION 5: FIRE-FIGHTING MEASURES

FLAMMABLE LIMITS IN AIR, UPPER:
(% BY VOLUME) LOWER:

FLASH POINT:
F: 435F
C: ,224C
METHOD USED: COC

AUTOIGNITION TEMPERATURE:
F:
C:

NFPA HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
OTHER:

HMIS HAZARD CLASSIFICATION
HEALTH: FLAMMABILITY: REACTIVITY:
PROTECTION:

EXTINGUISHING MEDIA: USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON
DIOXIDE. DO NOT USE A DIRECT STREAM OF WATER. PRODUCT WILL FLOAT &
REIGNITE.


SPECIAL FIRE FIGHTING PROCEDURES: USE WATER FOG, FOAM, DRY CHEMICAL OR CARBON
DIOXIDE. DO NOT USE A DIRECT STREAM OF WATER. PRODUCT WILL FLOAT &
REIGNITE.

UNUSUAL FIRE AND EXPLOSION HAZARDS: NONE

HAZARDOUS DECOMPOSITION PRODUCTS: NONE


SECTION 5 NOTES:


SECTION 6: ACCIDENTAL RELEASE MEASURES

ACCIDENTAL RELEASE MEASURES: Spill Release Procedures:MAY BURN ALTHOUGH NOT READILY IGNITABLE. USE
CAUTIOUS JUDGEMENT WHEN CLEANING UP LARGE MOLTEN SPILLS. FOR LARGE
MOLTEN SPILLS, WEAR RESPIRATOR AND PROTECTIVE CLOTHING AS
APPROPRIATE. SHUT OF SOURCE OR LEAK IF POSSIBLE. DIKE AND CONTAIN.
Neutralizing Agent:NONE



SECTION 6 NOTES:






SECTION 7: HANDLING AND STORAGE

HANDLING AND STORAGE:
STORE IN A COOL, DRY AREA.


OTHER PRECAUTIONS: MINIMIZE BREATHING OF VAPORS, MIST OR FUMES. AVOID
CONTACT WITH HOT MATERIALS.


SECTION 7 NOTES:


SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

ENGINEERING CONTROLS:

VENTILATION : USE VENTILATION AS REQUIRED TO CONTROL VAPOR
CONCENTRATIONS.


RESPIRATORY PROTECTION: USE A NIOSH-APPROVED RESPIRATOR AS REQUIRED TO
PREVENT OVEREXPOSURE. USE EITHER AN ATMOSPHERE-SUPPLYING RESPIRATOR
OR AN AIR-PURIFYING RESPIRATOR FOR PARTICULATES.


EYE PROTECTION: SAFETY GLASSES OR GOGGLES.

SKIN PROTECTION:

OTHER PROTECTIVE CLOTHING OR EQUIPMENT: PROTECTIVE CLOTHING AS REQUIRED

WORK HYGIENIC PRACTICES: NORMAL PRACTICES

EXPOSURE GUIDELINES:


SECTION 8 NOTES:



SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE:

ODOR: SLIGHT

PHYSICAL STATE: STABLE

pH AS SUPPLIED:
pH (Other):
BOILING POINT:
F: 650F
C: 343C
MELTING POINT:
F: 168F
C: 76C
FREEZING POINT:
F:
C:
VAPOR PRESSURE (mmHg):
@
F:
C:
VAPOR DENSITY (AIR = 1):
@
F:
C:
SPECIFIC GRAVITY (H2O = 1): 0.917

@
F:
C:
EVAPORATION RATE:

BASIS (=1):




SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (conít)

SOLUBILITY IN WATER:

PERCENT SOLIDS BY WEIGHT:

PERCENT VOLATILE:
BY WT/ BY VOL @
F:
C:
VOLATILE ORGANIC COMPOUNDS (VOC):

WITH WATER: LBS/GAL
WITHOUT WATER: LBS/GAL

MOLECULAR WEIGHT:
VISCOSITY:
@
F:
C:

SECTION 9 NOTES:


SECTION 10: STABILITY AND REACTIVITY

page 5

STABILITY:

CONDITIONS TO AVOID (STABILITY):

INCOMPATIBILITY (MATERIAL TO AVOID):

HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:

HAZARDOUS POLYMERIZATION:

CONDITIONS TO AVOID (POLYMERIZATION):


SECTION 10 NOTES:


SECTION 11: TOXICOLOGICAL INFORMATION

TOXICOLOGICAL INFORMATION:

SECTION 11 NOTES:


SECTION 12: ECOLOGICAL INFORMATION

ECOLOGICAL INFORMATION:


SECTION 12 NOTES:


SECTION 13: DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHOD:

RCRA HAZARD CLASS:




SECTION 13: DISPOSAL CONSIDERATIONS (conít)

SECTION 13 NOTES:


SECTION 14: TRANSPORT INFORMATION

U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENT:


WATER TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:
PACKING GROUP:
LABEL STATEMENTS:


AIR TRANSPORTATION
PROPER SHIPPING NAME:
HAZARD CLASS:
ID NUMBER:





| Return Home | FAQ Page | MSDS |
 
 



Copyright © 2012, Microstar Dental . All rights reserved.